Wayne 360516-001 User Manual download pdf (Page 2)

Operating Instructions and Parts Manual

www.waynepumps.com

so that the pump switches on with

approximately 14” of water in the sump.

3. While the pump is draining the pit,

verify that the discharge piping is

carrying the water to a point several

feet away from the foundation.

4. If the pump discharge line is

exposed to freezing temperature,

the exposed line must be pitched to

drain. Trapped water will freeze and

damage the pump.

Maintenance

Always

disconnect the electrical

supply before attempting to

install, service, relocate or

perform any maintenance. If the power

source is out of sight, lock and tag

in the open (off) position to prevent

unexpected power application. Failure

to do so could result in fatal electrical

shock. Only qualiﬁed electricians should

repair this unit. Improper repair could

result in fatal electrical shock.

1. Disassembly of the motor prior to

expiration of warranty will void the

warranty. If repairs are required, see

troubleshooting chart.

2. Keep pump inlet clean and free

of all foreign objects and inspect

annually. A clogged inlet will

damage pump.

3. Check pump monthly for proper

operation.

NOTE: A pump that has a tripped

thermal protector may start suddenly!

Installation

1. A ground fault circuit interrupter

(GFCI) is required.

2. This pump is for use on 120 Volt

(single phase), 60 hz, 15 amp service

and is equipped with a 3 conductor

cord and a 3 prong grounding plug.

3. Install pump in a sump pit with

minimum size as shown (See Figure

1). Construct sump pit of tile,

concrete, steel or plastic.

4. Locate unit on a solid, level

foundation. Do not place pump

directly on clay, earth, gravel or

sandy surface. These surfaces contain

small stones, gravel, sand, etc. that

may clog or damage the pump and

cause pump failure (See Figure 1).

5. (Optional) Thread check valve (not

included) into pump body carefully

to avoid stripping or cross threading.

Do not use pipe joint sealant.

6. Connect 1-1/4” rigid pipe to rubber

boot on check valve. Reverse boot

for 1-1/2” diameter pipe. Tighten

hose clamps.

Support pump and

piping when

assembling and after installation. Failure

to do so could cause piping to break, pump

to fail, etc. which could result in property

damage and/or personal injury.

Flood risk. If

ﬂexible discharge

hose is used, make sure pump is

secured in sump pit to prevent

movement. Failure to secure pump

could allow pump movement and switch

interference and prevent pump from

starting or stopping.

IMPORTANT: Make sure there is

adequate room for float switch to move

freely during operation.

7. Protect electrical cord from sharp

objects, hot surfaces, oil and

chemicals. Avoid kinking the

cord and replace damaged cords

immediately.

8. A sump pit cover must be installed

to prevent debris from clogging or

damaging the pump.

Risk of

electrical

shock! This pump is supplied

with a grounding conductor

and grounding type attachment plug. Use

a grounded GFCI receptacle to reduce the

risk of fatal electrical shock.

Never cut off the round grounding

prong. Cutting the cord or plug will

void the warranty and make the

pump inoperable.

9. Insert the float switch cord plug

directly into a 120 volt outlet (See

Figure 2).

ADJUST AND T EST

1. Fill sump with water.

2. Adjust rubber grommet into a

permanent position on float rod

Troubleshooting Chart

Symptom Possible Cause(s) Corrective Action

Pump will not start or

run

1. Blown fuse

2. Low line voltage

3. Defective motor

4. Defective switch

5. Impeller

6. Float obstructed

1. If blown, replace with proper sized fuse or reset breaker

2. If voltage is under 108 volts, check wiring size

- DO NOT USE AN EXTENSION CORD

3. Replace motor or pump

4. Replace switch

5. If impeller will not turn, remove housing and remove blockage

6. Make sure float moves freely up and down

Pump start and stops too

often

1. Back flow of water from piping

2. Float out of adjustment

1. Install or replace check valve (Wayne check valve kit #66005-WYN1)

2. Adjust grommet

Pump will not shut off

or thermal protector

turns off

1. Defective switch

2. Obstacle in piping

3. Float obstructed

1. Replace switch

2. Remove pump and clean pump and piping

3. Make sure float moves freely up and down

Pump operates but

delivers little or no

water

1. Low line voltage

2. Plugged impeller

1. If voltage is under 108 volts, check wiring size

- DO NOT USE AN EXTENSION CORD

2. Clean out impeller

Grounding

Blade

Grounded

Outlet

Power

Cord

TEST

RESET

Figure 2

GFCI

Outlet

1 2 3 4 5 6 7 ... 11 12

Comments to this Manuals

No comments

Wayne 360516-001 User Manual Page 2

Comments to this Manuals

Related products and manuals for Pumps Wayne 360516-001